[Docs] [txt|pdf] [Tracker] [Email] [Diff1] [Diff2] [Nits]
Versions: 00 01 02 03 04 05 06 07 08 09 10 11
12 13 14 15 16 17 RFC 6709
Network Working Group B. Carpenter
Internet-Draft B. Aboba (ed)
Intended Status: Informational S. Cheshire
Expires: August 4, 2011 Internet Architecture Board
4 February 2011
Design Considerations for Protocol Extensions
draft-iab-extension-recs-05
Abstract
This document discusses issues related to the extensibility of
Internet protocols, with a focus on the architectural design
considerations involved. Case study examples are included. It is
intended to assist designers of both base protocols and extensions.
Status of this Memo
This Internet-Draft is submitted to IETF in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
This Internet-Draft will expire on August 4, 2011.
IAB Informational [Page 1]
Internet-Draft Design Considerations for Extensions 4 February 2011
Copyright Notice
Copyright (c) 2011 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the BSD License.
This document may contain material from IETF Documents or IETF
Contributions published or made publicly available before November
10, 2008. The person(s) controlling the copyright in some of this
material may not have granted the IETF Trust the right to allow
modifications of such material outside the IETF Standards Process.
Without obtaining an adequate license from the person(s) controlling
the copyright in such materials, this document may not be modified
outside the IETF Standards Process, and derivative works of it may
not be created outside the IETF Standards Process, except to format
it for publication as an RFC or to translate it into languages other
than English.
IAB Informational [Page 2]
Internet-Draft Design Considerations for Extensions 4 February 2011
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.1 Requirements Language . . . . . . . . . . . . . . . . . . 4
2. Extension Documentation and Review . . . . . . . . . . . . . . 5
2.1 When is an Extension Routine? . . . . . . . . . . . . . . 5
2.2 What Constitutes a Major Extension? . . . . . . . . . . . 6
3. Architectural Principles . . . . . . . . . . . . . . . . . . . 7
3.1 Limited Extensibility . . . . . . . . . . . . . . . . . . 8
3.2 Design for Global Interoperability . . . . . . . . . . . . 8
3.3 Architectural Compatibility . . . . . . . . . . . . . . . 9
3.4 Protocol Variations . . . . . . . . . . . . . . . . . . . 9
3.5 Testability . . . . . . . . . . . . . . . . . . . . . . . 11
3.6 Parameter Parameter Registration . . . . . . . . . . . . . 11
3.7 Extensions to Critical Infrastructure . . . . . . . . . . 12
4. Considerations for the Base Protocol . . . . . . . . . . . . . 13
4.1 Version Numbers . . . . . . . . . . . . . . . . . . . . . 13
4.2 Reserved Fields . . . . . . . . . . . . . . . . . . . . . 16
4.3 Encoding Formats . . . . . . . . . . . . . . . . . . . . . 16
4.4 Parameter Space Design . . . . . . . . . . . . . . . . . . 16
4.5 Cryptographic Agility . . . . . . . . . . . . . . . . . . 19
5. Security Considerations . . . . . . . . . . . . . . . . . . . 20
6. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 20
7. References . . . . . . . . . . . . . . . . . . . . . . . . . . 20
7.1 Normative References . . . . . . . . . . . . . . . . . . . 20
7.2 Informative References . . . . . . . . . . . . . . . . . . 20
Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . . . 24
IAB Members . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Appendix A - Examples . . . . . . . . . . . . . . . . . . . . . . 25
A.1 Already documented cases . . . . . . . . . . . . . . . . . 25
A.2 RADIUS Extensions . . . . . . . . . . . . . . . . . . . . 25
A.3 TLS Extensions . . . . . . . . . . . . . . . . . . . . . . 26
A.4 L2TP Extensions . . . . . . . . . . . . . . . . . . . . . 28
Change log . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 30
IAB Informational [Page 3]
Internet-Draft Design Considerations for Extensions 4 February 2011
1. Introduction
Internet Engineering Task Force (IETF) protocols typically include
mechanisms whereby they can be extended in the future. It is of
course a good principle to design extensibility into protocols; one
common definition of a successful protocol is one that becomes widely
used in ways not originally anticipated, as described in "What Makes
for a Successful Protocol" [RFC5218]. Well-designed extensibility
mechanisms facilitate the evolution of protocols and help make it
easier to roll out incremental changes in an interoperable fashion.
When an initial protocol design is extended, there is always a risk
of unintended consequences, such as interoperability problems or
security vulnerabilities. This risk is especially high if the
extension is performed by a different team than the original
designers, who may stray outside implicit design constraints or
assumptions. As a result, extensions should be done carefully and
with a full understanding of the base protocol, existing
implementations, and current operational practice.
This is hardly a recent concern. "TCP Extensions Considered Harmful"
[RFC1263] was published in 1991. "Extend" or "extension" occurs in
the title of more than 400 existing Request For Comment (RFC)
documents. Yet generic extension considerations have not been
documented previously.
This document describes technical considerations for protocol
extensions, in order to minimize such risks. It is intended to
assist designers of both base protocols and extensions. Formal
procedures for extending IETF protocols are discussed in "Procedures
for Protocol Extensions and Variations" BCP 125 [RFC4775].
Section 2 discusses extension documentation and review. Section 3
describes architectural principles for protocol extensibility.
Section 4 explains how designers of base protocols can take steps to
anticipate and facilitate the creation of such subsequent extensions
in a safe and reliable manner. Readers are advised to study the
whole document, since the considerations are closely linked.
1.1. Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in BCP 14, RFC 2119
[RFC2119].
IAB Informational [Page 4]
Internet-Draft Design Considerations for Extensions 4 February 2011
2. Extension Documentation and Review
One of the pre-requisites for interoperable extensibility is proper
documentation and review.
Protocol components that are designed with the specific intention of
allowing extensibility should be clearly identified, with specific
and complete instructions on how to extend them. This includes the
process for adequate review of extension proposals: do they need
community review and if so how much and by whom?
The level of review required for protocol extensions will typically
vary based on the nature of the extension. Routine extensions may
require minimal review, while major extensions may require wide
review. Guidance on which extensions may be considered 'routine' and
which ones are 'major' are provided in the sections that follow.
To help future extension writers to use extension mechanisms
properly, there may be a need for explicit guidance relating to
extensions beyond what is encapsulated in the IANA considerations
section of the base specification.
Protocols whose data model is likely to be widely extended
(particularly using vendor-specific elements) should have a Design
Guidelines document specifically addressing extensions. For example,
"Guidelines for Authors and Reviewers of MIB Documents" [RFC4181]
provides valuable guidance to protocol designers creating new MIB
modules.
2.1. When is an Extension Routine?
An extension may be considered 'routine' if it amounts to a new data
element of a type that is already supported within the data model,
and if its handling is opaque to the protocol itself (e.g. does not
substantially change the pattern of messages and responses).
For this to apply, the protocol must have been designed to carry the
proposed data type, so that no changes to the underlying base
protocol or existing implementations are needed to carry the new data
element.
Moreover, no changes should be required to existing and currently
deployed implementations of the underlying protocol unless they want
to make use of the new data element. Using the existing protocol to
carry a new data element should not impact existing implementations
or cause operational problems. This typically requires that the
protocol silently discard unknown data elements.
IAB Informational [Page 5]
Internet-Draft Design Considerations for Extensions 4 February 2011
Examples of routine extensions include the Dynamic Host Configuration
Protocol (DHCP) vendor-specific option [RFC2132], RADIUS Vendor-
Specific Attributes [RFC2865], the enterprise Object IDentifier (OID)
tree for Management Information Base (MIB) modules, vendor
Multipurpose Internet Mail Extension (MIME) types, and some classes
of (non-critical) certification extensions. Such extensions can
safely be made with minimal discussion.
In order to increase the likelihood that routine extensions are truly
routine, protocol documents should provide guidelines explaining how
extensions should be performed. For example, even though DHCP
carries opaque data, defining a new option using completely
unstructured data may lead to an option that is unnecessarily hard
for clients and servers to process.
Processes that allow routine extensions with minimal or no review
should be used sparingly (such as the "First Come First Served"
allocation policy described in "Guidelines for Writing an IANA
Considerations Section in RFCs" [RFC5226]). In particular, they
should be limited to cases that are unlikely to cause protocol
failures, such as allowing new opaque data elements.
2.2. What Constitutes a Major Extension?
Major extensions may have characteristics leading to a risk of
interoperability failure. Where these characteristics are present,
it is necessary to pay extremely close attention to backward
compatibility with implementations and deployments of the unextended
protocol, and to the risk of inadvertent introduction of security or
operational exposures.
Extension designers should examine their design for the following
issues:
1. Modifications or extensions to the working of the underlying
protocol. This can include changing the semantics of existing
Protocol Data Units (PDUs) or defining new message types that may
require implementation changes in existing and deployed
implementations of the protocol, even if they do not want to make
use of the new functions or data types. A base protocol without a
"silent discard" rule for unknown data elements may automatically
enter this category, even for apparently minor extensions.
2. Changes to the transport model. While there are circumstances
where specification of additional transport protocols may make
sense, removal of a widely implemented transport protocol is
highly likely to result in interoperability problems and thus
should be avoided wherever possible.
IAB Informational [Page 6]
Internet-Draft Design Considerations for Extensions 4 February 2011
Where additional transports are specified, one way to avoid issues
is to mandate support for a single transport protocol, while
designating other transport protocols as optional. However, if
optional transport protocols are introduced due to the unique
advantages they afford in certain scenarios, in those situations
implementations not supporting optional transport protocols may
exhibit degraded performance or may even fail.
While requiring support for multiple transport protocols may
appear attractive, authors need to realistically evaluate the
likelihood that implementers will conform to the requirements.
For example, where resources are limited (such as in embedded
systems), implementers may choose to only support a subset of the
mandated transport protocols, resulting in non-interoperable
protocol variants.
3. Changes to the basic architectural assumptions. This may
include architectural assumptions that are explicitly stated or
those that have been assumed by implementers. For example, this
would include adding a requirement for session state to a
previously stateless protocol.
4. New usage scenarios not originally intended or investigated.
This can potentially lead to operational difficulties when
deployed, even in cases where the "on-the-wire" format has not
changed. For example, the level of traffic carried by the
protocol may increase substantially, packet sizes may increase,
and implementation algorithms that are widely deployed may not
scale sufficiently or otherwise be up to the new task at hand.
For example, a new DNS Resource Record (RR) type that is too big
to fit into a single UDP packet could cause interoperability
problems with existing DNS clients and servers.
3. Architectural Principles
This section describes basic principles of protocol extensibility:
1. Extensibility features should be limited to what is reasonably
anticipated when the protocol is developed.
2. Protocol extensions should be designed for global
interoperability.
3. Protocol extensions should be architecturally compatible with
the base protocol.
4. Protocol extension mechanisms should not be used to create
incompatible protocol variations.
IAB Informational [Page 7]
Internet-Draft Design Considerations for Extensions 4 February 2011
5. Extension mechanisms need to be testable.
6. Protocol parameter assignments need to be coordinated to avoid
potential conflicts.
7. Extensions to critical infrastructure require special care.
3.1. Limited Extensibility
Designing a protocol for extensibility may have the perverse side
effect of making it easy to construct incompatible extensions.
Consequently, protocols should not be made more extensible than
clearly necessary at inception, and the process for defining new
extensibility mechanisms should ensure that adequate review of
proposed extensions will take place before widespread adoption.
3.2. Design for Global Interoperability
The IETF mission [RFC3935] is to create interoperable protocols for
the global Internet, not a collection of different incompatible
protocols (or "profiles") for use in separate private networks.
Experience shows that separate private networks often end up using
equipment from the same vendors, or end up having portable equipment
like laptop computers move between them, and networks that were
originally envisaged as being separate can end up being connected
later.
As a result, extensions cannot be designed for an isolated
environment; instead, extension designers must assume that systems
using the extension will need to interoperate with systems on the
global Internet.
A key requirement for interoperable extension design is that the base
protocol must be well designed for interoperability, and that
extensions must have unambiguous semantics. Ideally, the protocol
mechanisms for extension and versioning should be sufficiently well
described that compatibility can be assessed on paper. Otherwise,
when two "private" extensions encounter each other on a public
network, unexpected interoperability problems may occur.
Consider a "private" extension installed on a work computer which,
being portable, is sometimes connected to a home network or a hotel
network. If the "private" extension is incompatible with an
unextended version of the same protocol, problems will occur.
Similarly, problems can occur if "private" extensions conflict with
each other. For example, imagine the situation where one site chose
to use DHCP [RFC2132] option code 62 for one meaning, and a different
IAB Informational [Page 8]
Internet-Draft Design Considerations for Extensions 4 February 2011
site chose to use DHCP option code 62 for a completely different,
incompatible, meaning. It may be impossible for a vendor of portable
computing devices to make a device that works correctly in both
environments.
One approach to solving this problem has been to reserve parts of an
identifier namespace for "site-specific" or "experimental" use, such
as "X-" headers in email messages [RFC0822]. This problem with this
approach is that when an experiment turns out to be successful, or a
site-specific use turns out to have applicability elsewhere, other
vendors will then implement that "X-" header for interoperability,
and the "X-" header becomes a de facto standard, meaning that it is
no longer true that any header beginning "X-" is site-specific or
experimental. The notion of "X-" headers was removed from the
Internet Message Format standard when it was was updated in 2001
[RFC2822].
3.3. Architectural Compatibility
Since protocol extension mechanisms may impact interoperability, it
is important that they be architecturally compatible with the base
protocol. As part of the definition of new extension mechanisms, it
is important to address whether the mechanisms make use of features
as envisaged by the original protocol designers, or whether a new
extension mechanism is being invented. If a new extension mechanism
is being invented, then architectural compatibility issues need to be
addressed.
Documents relying on extension mechanisms need to explicitly identify
the mechanisms being relied upon. Where extension guidelines are
available, mechanisms need to indicate whether they are compliant
with those guidelines and if not, why not. For example, a document
defining new data elements should not implicitly define new data
types or protocol operations without explicitly describing those
dependencies and discussing their impact.
3.4. Protocol Variations
Protocol variations - specifications that look very similar to the
original but don't interoperate with each other or with the original
- are even more harmful to interoperability than extensions. In
general, such variations should be avoided. Causes of protocol
variations include incompatible protocol extensions, uncoordinated
protocol development, and poorly designed "profiles".
Protocol extension mechanisms should not be used to create
incompatible forks in development. An extension may lead to
interoperability failures unless the extended protocol correctly
IAB Informational [Page 9]
Internet-Draft Design Considerations for Extensions 4 February 2011
supports all mandatory and optional features of the unextended base
protocol, and implementations of the base protocol operate correctly
in the presence of the extensions. In addition, it is necessary for
an extension to interoperate with other extensions.
As noted in "Uncoordinated Protocol Development Considered Harmful"
[RFC5704], incompatible forks in development can result from the
uncoordinated adaptation of a protocol, parameter or code-point.
Section 1 of [RFC5704] states:
In particular, the IAB considers it an essential principle of the
protocol development process that only one SDO maintains design
authority for a given protocol, with that SDO having ultimate
authority over the allocation of protocol parameter code-points
and over defining the intended semantics, interpretation, and
actions associated with those code-points.
Profiling is a common technique for improving interoperability within
a target environment or set of scenarios. Typically, profiles are
constructed by narrowing potential implementation choices or by
removing protocol features. However, in order to avoid creating
interoperability problems when profiled implementations interact with
others over the Global Internet, profilers need to remain cognizant
of the implications of normative requirements.
As noted in "Key words for use in RFCs to Indicate Requirement
Levels" [RFC2119] Section 6, imperatives are to be used with care,
and as a result, their removal within a profile is likely to result
in serious consequences:
Imperatives of the type defined in this memo must be used with
care and sparingly. In particular, they MUST only be used where
it is actually required for interoperation or to limit behavior
which has potential for causing harm (e.g., limiting
retransmissions) For example, they must not be used to try to
impose a particular method on implementors where the method is not
required for interoperability.
As noted in [RFC2119] Sections 3 and 4, recommendations also cannot
be removed from profiles without serious consideration:
there may exist valid reasons in particular circumstances to
ignore a particular item, but the full implications must be
understood and carefully weighed before choosing a different
course.
As noted in [RFC2119] Section 5, implementations which do not support
optional features still retain the obligation to ensure
IAB Informational [Page 10]
Internet-Draft Design Considerations for Extensions 4 February 2011
interoperation with implementations that do:
An implementation which does not include a particular option MUST
be prepared to interoperate with another implementation which does
include the option, though perhaps with reduced functionality. In
the same vein an implementation which does include a particular
option MUST be prepared to interoperate with another
implementation which does not include the option (except, of
course, for the feature the option provides.)
3.5. Testability
Experience has shown that it is insufficient merely to correctly
specify extensibility and backwards compatibility in an RFC. It is
also important that implementations respect the compatibility
mechanisms; if not, non-interoperable pairs of implementations may
arise. The TLS case study (Appendix A.3) shows how important this
can be.
In order to determine whether protocol extension mechanisms have been
properly implemented, testing is required. However, for this to be
possible, test cases need to be developed. If a base protocol
document specifies extension mechanisms but does not utilize them or
provide examples, it may not be possible to develop effective test
cases based on the base protocol specification alone. As a result,
base protocol implementations may not be properly tested and non-
compliant extension behavior may not be detected until these
implementations are widely deployed.
To encourage correct implementation of extension mechanisms, base
protocol specifications should clearly articulate the expected
behavior of extension mechanisms and should include examples of
correct and incorrect extension behavior.
3.6. Protocol Parameter Registration
An extension is often likely to make use of additional values added
to an existing IANA registry (in many cases, simply by adding a new
Type-Length-Value (TLV) field). To avoid conflicting usage of the
same value, as well as to prevent potential difficulties in
determining and transferring parameter ownership, it is essential
that all new values are properly registered by the applicable
procedures.
For general rules see "Guidelines for Writing an IANA Considerations
Section in RFCs" [RFC5226], and for specific rules and registries see
the individual protocol specification RFCs and the IANA web site. If
this is not done, there is nothing to prevent two different
IAB Informational [Page 11]
Internet-Draft Design Considerations for Extensions 4 February 2011
extensions picking the same value. When these two extensions "meet"
each other on the Internet, failure is inevitable.
A surprisingly common case of this is misappropriation of assigned
Transmission Control Protocol (TCP) (or User Datagram Protocol (UDP))
registered port numbers. This can lead to a client for one service
attempting to communicate with a server for another service.
Numerous cases could be cited, but not without embarrassing specific
implementers.
While in theory a "standards track" or "IETF consensus" parameter
allocation policy may be instituted to encourage protocol parameter
registration or to improve interoperability, in practice these
policies, if administered clumsily, can have the opposite effect,
discouraging protocol parameter registration and encouraging rampant
self-allocation. These effects have also been observed in a number
of instances.
In some cases, it may be appropriate to use values designated as
"experimental" or "local use" in early implementations of an
extension. For example, "Experimental Values in IPv4, IPv6, ICMPv4,
ICMPv6, UDP and TCP Headers" [RFC4727] discusses experimental values
for IP and transport headers, and "Definition of the Differentiated
Services Field (DS Field) in the IPv4 and IPv6 Headers" [RFC2474]
defines experimental/local use ranges for differentiated services
code points. Such values should be used with care and only for their
stated purpose: experiments and local use. They are unsuitable for
Internet-wide use, since they may be used for conflicting purposes
and thereby cause interoperability failures. Packets containing
experimental or local use values must not be allowed out of the
domain in which they are meaningful.
3.7. Extensions to Critical Infrastructure
Some protocols (such as Domain Name Service (DNS) and Border Gateway
Protocol (BGP)) have become critical components of the Internet
infrastructure. When such protocols are extended, the potential
exists for negatively impacting the reliability and security of the
global Internet.
As a result, special care needs to be taken with these extensions,
such as taking explicit steps to isolate existing uses from new ones.
For example, this can be accomplished by requiring the extension to
utilize a different port or multicast address, or by implementing the
extension within a separate process, without access to the data and
control structures of the base protocol.
IAB Informational [Page 12]
Internet-Draft Design Considerations for Extensions 4 February 2011
4. Considerations for the Base Protocol
Good extension design depends on a well designed base protocol.
Interoperability stems from a number of factors, including:
1. A well-written specification. Does the specification make
clear what an implementor needs to support and does it define the
impact that individual operations (e.g. a message sent to a peer)
will have when invoked?
2. Design for deployability. This includes understanding what
current implementations do and how a proposed extension will
interact with deployed systems. Will a proposed extension (or its
proposed usage) operationally stress existing implementations or
the underlying protocol itself if widely deployed?
3. An adequate transition or coexistence story. What impact will
the proposed extension have on implementations that do not
understand it? Is there a way to negotiate or determine the
capabilities of a peer? Can the extended protocol negotiate with
an unextended partner to find a common subset of useful functions?
4. Respecting underlying architectural or security assumptions.
This includes assumptions that may not be well-documented, those
that may have arisen as the result of operational experience, or
those that only became understood after the original protocol was
published. For example, do the extensions reverse the flow of
data, allow formerly static parameters to be changed on the fly,
or change assumptions relating to the frequency of reads/writes?
5. Minimizing impact on critical infrastructure. Does the
proposed extension (or its proposed usage) have the potential for
negatively impacting critical infrastructure to the point where
explicit steps would be appropriate to isolate existing uses from
new ones?
6. Data model extensions. Does the proposed extension extend the
data model in a major way? For example, are new data types
defined that may require code changes within existing
implementations?
4.1. Version Numbers
Any mechanism for extension by versioning must include provisions to
ensure interoperability, or at least clean failure modes. Imagine
someone creating a protocol and using a "version" field and
populating it with a value (1, let's say), but giving no information
about what would happen when a new version number appears in it.
IAB Informational [Page 13]
Internet-Draft Design Considerations for Extensions 4 February 2011
That's bad protocol design and description; it should be clear what
the expectation is and how you test it. For example, stating that
1.X must be compatible with any version 1 code, but version 2 or
greater is not expected to be compatible, has different implications
than stating that version 1 must be a proper subset of version 2.
An example is ROHC (Robust Header Compression). ROHCv1 [RFC3095]
supports a certain set of profiles for compression algorithms. But
experience had shown that these profiles had limitations, so the ROHC
WG developed ROHCv2 [RFC5225]. A ROHCv1 implementation does not
contain code for the ROHCv2 profiles. As the ROHC WG charter said
during the development of ROHCv2:
It should be noted that the v2 profiles will thus not be
compatible with the original (ROHCv1) profiles, which means less
complex ROHC implementations can be realized by not providing
support for ROHCv1 (over links not yet supporting ROHC, or by
shifting out support for ROHCv1 in the long run). Profile support
is agreed through the ROHC channel negotiation, which is part of
the ROHC framework and thus not changed by ROHCv2.
Thus in this case both backwards-compatible and backwards-
incompatible deployments are possible. The important point is a
clearly thought out approach to the question of operational
compatibility. In the past, protocols have utilized a variety of
strategies for versioning, many of which have proven problematic.
These include:
1. No versioning support. This approach is exemplified by
Extensible Authentication Protocol (EAP) [RFC3748] as well as
Remote Authentication Dial In User Service (RADIUS) [RFC2865],
both of which provide no support for versioning. While lack of
versioning support protects against the proliferation of
incompatible dialects, the need for extensibility is likely to
assert itself in other ways, so that ignoring versioning entirely
may not be the most forward thinking approach.
2. Highest mutually supported version (HMSV). In this approach,
implementations exchange the version numbers of the highest
version each supports, with the negotiation agreeing on the
highest mutually supported protocol version. This approach
implicitly assumes that later versions provide improved
functionality, and that advertisement of a particular version
number implies support for all lower version numbers. Where these
assumptions are invalid, this approach breaks down, potentially
resulting in interoperability problems. An example of this issue
occurs in Protected EAP [PEAP] where implementations of higher
versions may not necessarily provide support for lower versions.
IAB Informational [Page 14]
Internet-Draft Design Considerations for Extensions 4 February 2011
3. Assumed backward compatibility. In this approach,
implementations may send packets with higher version numbers to
legacy implementations supporting lower versions, but with the
assumption that the legacy implementations will interpret packets
with higher version numbers using the semantics and syntax defined
for lower versions. This is the approach taken by Port-Based
Access Control [IEEE-802.1X]. For this approach to work, legacy
implementations need to be able to accept packets of known type
with higher protocol versions without discarding them; protocol
enhancements need to permit silent discard of unsupported
extensions; implementations supporting higher versions need to
refrain from mandating new features when encountering legacy
implementations.
4. Major/minor versioning. In this approach, implementations with
the same major version but a different minor version are assumed
to be backward compatible, but implementations are assumed to be
required to negotiate a mutually supported major version number.
This approach assumes that implementations with a lower minor
version number but the same major version can safely ignore
unsupported protocol messages.
5. Min/max versioning. This approach is similar to HMSV, but
without the implied obligation for clients and servers to support
all versions back to version 1, in perpetuity. It allows clients
and servers to cleanly drop support for early versions when those
versions become so old that they are no longer relevant and no
longer required. In this approach, the client initiating the
connection reports the highest and lowest protocol versions it
understands. The server reports back the chosen protocol version:
a. If the server understands one or more versions in the client's
range, it reports back the highest mutually understood version.
b. If there is no mutual version, then the server reports back
some version that it does understand (selected as described
below). The connection is then typically dropped by client or
server, but reporting this version number first helps facilitate
useful error messages at the client end:
* If there is no mutual version, and the server speaks any
version higher than client max, it reports the lowest version it
speaks which is greater than the client max. The client can
then report to the user, "You need to upgrade to at least
version <xx>."
* Else, the server reports the highest version it speaks. The
client can then report to the user, "You need to request the
IAB Informational [Page 15]
Internet-Draft Design Considerations for Extensions 4 February 2011
server operator to upgrade to at least version <min>."
Protocols generally do not need any version-negotiation mechanism
more complicated than the mechanisms described here. The nature of
protocol version-negotiation mechanisms is that, by definition, they
don't get widespread real-world testing until *after* the base
protocol has been deployed for a while, and its deficiencies have
become evident. This means that, to be useful, a protocol version
negotiation mechanism should be simple enough that it can reasonably
be assumed that all the implementers of the first protocol version at
least managed to implement the version-negotiation mechanism
correctly.
4.2. Reserved Fields
Protocols commonly include one or more "reserved" fields, clearly
intended for future extensions. It is good practice to specify the
value to be inserted in such a field by the sender (typically zero)
and the action to be taken by the receiver when seeing some other
value (typically no action). In packet format diagrams, such fields
are typically labeled "MBZ", to be read as, "Must Be Zero on
transmission, Must Be Ignored on reception." A common mistake of
inexperienced protocol implementers is to think that "MBZ" means that
it's their software's job to verify that the value of the field is
zero on reception, and reject the packet if not. This is a mistake,
and such software will fail when it encounters future versions of the
protocol where these previously reserved fields are given new defined
meanings. Similarly, protocols should carefully specify how
receivers should react to unknown TLVs etc., such that failures occur
only when that is truly the intended outcome.
4.3. Encoding Formats
Using widely-supported encoding formats leads to better
interoperability and easier extensibility. An excellent example is
the Simple Network Management Protocol (SNMP) SMI. Guidelines exist
for defining the MIB objects that SNMP carries [RFC4181]. Also,
multiple textual conventions have been published, so that MIB
designers do not have to reinvent the wheel when they need a commonly
encountered construct. For example, the "Textual Conventions for
Internet Network Addresses" [RFC4001] can be used by any MIB designer
needing to define objects containing IP addresses, thus ensuring
consistency as the body of MIBs is extended.
4.4. Parameter Space Design
In some protocols the parameter space is either infinite (e.g. Header
field names) or sufficiently large that it is unlikely to be
IAB Informational [Page 16]
Internet-Draft Design Considerations for Extensions 4 February 2011
exhausted. In other protocols, the parameter space is finite, and in
some cases, has proven inadequate to accommodate demand. Common
mistakes include:
a. A version field that is too small (e.g. two bits or less). When
designing a version field, existing as well as potential versions of
a protocol need to be taken into account. For example, if a protocol
is being standardized for which there are existing implementations
with known interoperability issues, more than one version for "pre-
standard" implementations may be required. If two "pre-standard"
versions are required in addition to a version for an IETF standard,
then a two-bit version field would only leave one additional version
code-point for a future update, which could be insufficient. This
problem was encountered during the development of the PEAPv2 protocol
[PEAP].
b. A small parameter space (e.g. 8-bits or less) along with a First
Come, First Served (FCFS) allocation policy. In general, an FCFS
allocation policy is only appropriate in situations where parameter
exhaustion is highly unlikely. In situations where substantial
demand is anticipated within a parameter space, the space should
either be designed to be sufficient to handle that demand, or vendor
extensibility should be provided to enable vendors to self-allocate.
The combination of a small parameter space, an FCFS allocation
policy, and no support for vendor extensibility is particularly
likely to prove ill-advised. An example of such a combination was
the design of the original 8-bit EAP Method Type space [RFC2284].
Once the potential for parameter exhaustion becomes apparent, it is
important that it be addressed as quickly as possible. Protocol
changes can take years to appear in implementations and by then the
exhaustion problem could become acute.
Options for addressing a protocol parameter exhaustion problem
include:
Rethinking the allocation regime
Where it becomes apparent that the size of a parameter space is
insufficient to meet demand, it may be necessary to rethink the
allocation mechanism, in order to prevent rapid parameter space
exhaustion. For example, a few years after approval of RFC 2284
[RFC2284], it became clear that the combination of a FCFS
allocation policy and lack of support for vendor-extensions had
created the potential for exhaustion of the EAP Method Type space
within a few years. To address the issue, [RFC3748] Section 6.2
changed the allocation policy for EAP Method Types from FCFS to
Expert Review, with Specification Required.
IAB Informational [Page 17]
Internet-Draft Design Considerations for Extensions 4 February 2011
Support for vendor-specific parameters
If the demand that cannot be accommodated is being generated by
vendors, merely making allocation harder could make things worse if
this encourages vendors to self-allocate, creating interoperability
problems. In such a situation, support for vendor-specific
parameters should be considered, allowing each vendor to self-
allocate within their own vendor-specific space based on a vendor's
Private Enterprise Code (PEC). For example, in the case of the EAP
Method Type space, [RFC3748] Section 6.2 also provided for an
Expanded Type space for "functions specific only to one vendor's
implementation".
Extensions to the parameter space
If the goal is to stave off exhaustion in the face of high demand,
a larger parameter space may be helpful. Where vendor-specific
parameter support is available, this may be achieved by allocating
an PEC for IETF use. Otherwise it may be necessary to try to extend
the size of the parameter fields, which could require a new
protocol version or other substantial protocol changes.
Parameter reclamation
In order to gain time, it may be necessary to reclaim unused
parameters. However, it may not be easy to determine whether a
parameter that has been allocated is in use or not, particularly if
the entity that obtained the allocation no longer exists or has
been acquired (possibly multiple times).
Parameter Transfer
When all the above mechanisms have proved infeasible and parameter
exhaustion looms in the near future, enabling the transfer of
ownership of protocol parameters can be considered as a means for
improving allocation efficiency. However, enabling transfer of
parameter ownership can be far from simple if the parameter
allocation process was not originally designed to enable title
searches and ownership transfers.
A parameter allocation process designed to uniquely allocate code-
points is fundamentally different from one designed to enable title
search and transfer. If the only goal is to ensure that a
parameter is not allocated more than once, the parameter registry
will only need to record the initial allocation. On the other
hand, if the goal is to enable transfer of ownership of a protocol
parameter, then it is important not only to record the initial
allocation, but also to track subsequent ownership changes, so as
to make it possible to determine and transfer title. Given the
difficulty of converting from a unique allocation regime to one
requiring support for title search and ownership transfer, it is
best for the desired capabilities to be carefully thought through
IAB Informational [Page 18]
Internet-Draft Design Considerations for Extensions 4 February 2011
at the time of registry establishment.
4.5. Cryptographic Agility
Extensibility with respect to cryptographic algorithms is desirable
in order to provide resilience against the compromise of any
particular algorithm. "Guidance for Authentication, Authorization,
and Accounting (AAA) Key Management" BCP 132 [RFC4962] Section 3
provides some basic advice:
The ability to negotiate the use of a particular cryptographic
algorithm provides resilience against compromise of a particular
cryptographic algorithm... This is usually accomplished by
including an algorithm identifier and parameters in the protocol,
and by specifying the algorithm requirements in the protocol
specification. While highly desirable, the ability to negotiate
key derivation functions (KDFs) is not required. For
interoperability, at least one suite of mandatory-to-implement
algorithms MUST be selected...
This requirement does not mean that a protocol must support both
public-key and symmetric-key cryptographic algorithms. It means
that the protocol needs to be structured in such a way that
multiple public-key algorithms can be used whenever a public-key
algorithm is employed. Likewise, it means that the protocol needs
to be structured in such a way that multiple symmetric-key
algorithms can be used whenever a symmetric-key algorithm is
employed.
In practice, the most difficult challenge in providing cryptographic
agility is providing for a smooth transition in the event that a
mandatory-to-implement algorithm is compromised. Since it may take
significant time to provide for widespread implementation of a
previously undeployed alternative, it is often advisable to recommend
implementation of alternative algorithms of distinct lineage in
addition to those made mandatory-to-implement, so that an alternative
algorithm is readily available. If such a recommended alternative is
not in place, then it would be wise to issue such a recommendation as
soon as indications of a potential weakness surface. This is
particularly important in the case of potential weakness in
algorithms used to authenticate and integrity-protect the
cryptographic negotiation itself, such as KDFs or message integrity
checks (MICs). Without secure alternatives to compromised KDF or MIC
algorithms, it may not be possible to secure the cryptographic
negotiation against a bidding-down attack while retaining backward
compatibility.
IAB Informational [Page 19]
Internet-Draft Design Considerations for Extensions 4 February 2011
5. Security Considerations
An extension must not introduce new security risks without also
providing adequate counter-measures, and in particular it must not
inadvertently defeat security measures in the unextended protocol.
Thus, the security analysis for an extension needs to be as thorough
as for the original protocol - effectively it needs to be a
regression analysis to check that the extension doesn't inadvertently
invalidate the original security model.
This analysis may be simple (e.g. adding an extra opaque data element
is unlikely to create a new risk) or quite complex (e.g. adding a
handshake to a previously stateless protocol may create a completely
new opportunity for an attacker).
When the extensibility of a design includes allowing for new and
presumably more powerful cryptographic algorithms to be added,
particular care is needed to ensure that the result is in fact
increased security. For example, it may be undesirable from a
security viewpoint to allow negotiation down to an older, less secure
algorithm.
6. IANA Considerations
[RFC Editor: please remove this section prior to publication.]
This document has no IANA Actions.
7. References
7.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC4775] Bradner, S., Carpenter, B., and T. Narten, "Procedures
for Protocol Extensions and Variations", BCP 125, RFC
4775, December 2006.
[RFC5226] Narten, T. and H. Alvestrand, "Guidelines for Writing an
IANA Considerations Section in RFCs", BCP 26, RFC 5226,
May 2008.
7.2. Informative References
[I-D.ietf-radext-design]
DeKok, A. and G. Weber, "RADIUS Design Guidelines",
draft-ietf-radext-design-19.txt, Internet draft (work in
IAB Informational [Page 20]
Internet-Draft Design Considerations for Extensions 4 February 2011
progress), November 2010.
[IEEE-802.1X] Institute of Electrical and Electronics Engineers, "Local
and Metropolitan Area Networks: Port-Based Network Access
Control", IEEE Standard 802.1X-2004, December 2004.
[PEAP] Palekar, A., Simon, D., Salowey, J., Zhou, H., Zorn, G.
and S. Josefsson, "Protected EAP Protocol (PEAP) Version
2", draft-josefsson-pppext-eap-tls-eap-10.txt, Expired
Internet draft (work in progress), October 2004.
[RFC0822] Crocker, D., "Standard for the format of ARPA Internet
text messages", STD 11, RFC 822, August 1982.
[RFC1263] O'Malley, S. and L. Peterson, "TCP Extensions Considered
Harmful", RFC 1263, October 1991.
[RFC2132] Alexander, S. and R. Droms, "DHCP Options and BOOTP
Vendor Extensions", RFC 2132, March 1997.
[RFC2246] Dierks, T. and C. Allen, "The TLS Protocol Version 1.0",
RFC 2246, January 1999.
[RFC2284] Blunk, L. and J. Vollbrecht, "PPP Extensible
Authentication Protocol (EAP)", RFC 2284, March 1998.
[RFC2474] Nichols, K., Blake, S., Baker, F., and D. Black,
"Definition of the Differentiated Services Field (DS
Field) in the IPv4 and IPv6 Headers", RFC 2474, December
1998.
[RFC2661] Townsley, W., Valencia, A., Rubens, A., Pall, G., Zorn,
G., and B. Palter, "Layer Two Tunneling Protocol "L2TP"",
RFC 2661, August 1999.
[RFC2671] Vixie, P., "Extension Mechanisms for DNS (EDNS0)",RFC
2671, August 1999.
[RFC2822] Resnick, P., "Internet Message Format", RFC 2822, April
2001.
[RFC2865] Rigney, C., Willens, S., Rubens, A., and W. Simpson,
"Remote Authentication Dial In User Service (RADIUS)",
RFC 2865, June 2000.
[RFC3095] Bormann, C., Burmeister, C., Degermark, M., Fukushima,
H., Hannu, H., Jonsson, L-E., Hakenberg, R., Koren, T.,
Le, K., Liu, Z., Martensson, A., Miyazaki, A., Svanbro,
IAB Informational [Page 21]
Internet-Draft Design Considerations for Extensions 4 February 2011
K., Wiebke, T., Yoshimura, T., and H. Zheng, "RObust
Header Compression (ROHC): Framework and four profiles:
RTP, UDP, ESP, and uncompressed", RFC 3095, July 2001.
[RFC3427] Mankin, A., Bradner, S., Mahy, R., Willis, D., Ott, J.,
and B. Rosen, "Change Process for the Session Initiation
Protocol (SIP)", BCP 67, RFC 3427, December 2002.
[RFC3575] Aboba, B., "IANA Considerations for RADIUS (Remote
Authentication Dial In User Service)", RFC 3575, July
2003.
[RFC3597] Gustafsson, A., "Handling of Unknown DNS Resource Record
(RR) Types", RFC 3597, September 2003.
[RFC3735] Hollenbeck, S., "Guidelines for Extending the Extensible
Provisioning Protocol (EPP)", RFC 3735, March 2004.
[RFC3748] Aboba, B., Blunk, L., Vollbrecht, J., Carlson, J. and H.
Lefkowetz, "Extensible Authentication Protocol (EAP)",
RFC 3748, June 2004.
[RFC3935] Alvestrand, H., "A Mission Statement for the IETF", RFC
3935, October 2004.
[RFC4001] Daniele, M., Haberman, B., Routhier, S., and J.
Schoenwaelder, "Textual Conventions for Internet Network
Addresses", RFC 4001, February 2005.
[RFC4181] Heard, C., "Guidelines for Authors and Reviewers of MIB
Documents", BCP 111, RFC 4181, September 2005.
[RFC4366] Blake-Wilson, S., Nystrom, M., Hopwood, D., Mikkelsen,
J., and T. Wright, "Transport Layer Security (TLS)
Extensions", RFC 4366, April 2006.
[RFC4485] Rosenberg, J. and H. Schulzrinne, "Guidelines for Authors
of Extensions to the Session Initiation Protocol (SIP)",
RFC 4485, May 2006.
[RFC4521] Zeilenga, K., "Considerations for Lightweight Directory
Access Protocol (LDAP) Extensions", BCP 118, RFC 4521,
June 2006.
[RFC4727] Fenner, B., "Experimental Values In IPv4, IPv6, ICMPv4,
ICMPv6, UDP, and TCP Headers", RFC 4727, November 2006.
IAB Informational [Page 22]
Internet-Draft Design Considerations for Extensions 4 February 2011
[RFC4929] Andersson, L. and A. Farrel, "Change Process for
Multiprotocol Label Switching (MPLS) and Generalized MPLS
(GMPLS) Protocols and Procedures", BCP 129, RFC 4929,
June 2007.
[RFC4962] Housley, R. and B. Aboba, "Guidance for Authentication,
Authorization, and Accounting (AAA) Key Management", BCP
132, RFC 4962, July 2007.
[RFC5080] Nelson, D. and A. DeKok, "Common Remote Authentication
Dial In User Service (RADIUS) Implementation Issues and
Suggested Fixes", RFC 5080, December 2007.
[RFC5218] Thaler, D., and B. Aboba, "What Makes for a Successful
Protocol?", RFC 5218, July 2008.
[RFC5225] Pelletier, G. and K. Sandlund, "RObust Header Compression
Version 2 (ROHCv2): Profiles for RTP, UDP, IP, ESP and
UDP-Lite", RFC 5225, April 2008.
[RFC5246] Dierks, T. and E. Rescorla, "The Transport Layer Security
(TLS) Protocol Version 1.2", RFC 5246, August 2008.
[RFC5704] Bryant, S. and M. Morrow, "Uncoordinated Protocol
Development Considered Harmful", RFC 5704, November 2009.
[RFC5727] Peterson, J., Jennings, C. and R. Sparks, "Change Process
for the Session Initiation Protocol (SIP) and the Real-
time Applications and Infrastructure Area", RFC 5727,
March 2010.
IAB Informational [Page 23]
Internet-Draft Design Considerations for Extensions 4 February 2011
Acknowledgments
This document is heavily based on an earlier draft under a different
title by Scott Bradner and Thomas Narten.
That draft stated: The initial version of this document was put
together by the IESG in 2002. Since then, it has been reworked in
response to feedback from John Loughney, Henrik Levkowetz, Mark
Townsley, Randy Bush and others.
Valuable comments and suggestions on the current form of the document
were made by Jari Arkko, Ted Hardie, Loa Andersson, Eric Rescorla,
Pekka Savola, Leslie Daigle, Alfred Hoenes, Adam Roach and Phillip
Hallam-Baker.
The text on TLS experience was contributed by Yngve Pettersen.
IAB Members at the Time of this Writing
Bernard Aboba
Marcelo Bagnulo
Ross Callon
Spencer Dawkins
Vijay Gill
Russ Housley
John Klensin
Olaf Kolkman
Danny McPherson
Jon Peterson
Andrei Robachevsky
Dave Thaler
Hannes Tschofenig
IAB Informational [Page 24]
Internet-Draft Design Considerations for Extensions 4 February 2011
Appendix A. Examples
This section discusses some specific examples, as case studies.
A.1. Already documented cases
There are certain documents that specify a change process or describe
extension considerations for specific IETF protocols:
The SIP change process [RFC3427], [RFC4485], [RFC5727]
The (G)MPLS change process (mainly procedural) [RFC4929]
LDAP extensions [RFC4521]
EPP extensions [RFC3735]
DNS extensions [RFC2671][RFC3597]
It is relatively common for MIBs, which are all in effect extensions
of the SMI data model, to be defined or extended outside the IETF.
BCP 111 [RFC4181] offers detailed guidance for authors and reviewers.
A.2. RADIUS Extensions
The RADIUS [RFC2865] protocol was designed to be extensible via
addition of Attributes to a Data Dictionary on the server, without
requiring code changes. However, this extensibility model assumed
that Attributes would conform to a limited set of data types and that
vendor extensions would be limited to use by vendors, in situations
in which interoperability was not required. Subsequent developments
have stretched those assumptions.
Section 6.2 of the RADIUS specification [RFC2865] defines a mechanism
for Vendor-Specific extensions (Attribute 26), and states that use of
Vendor-Specific extensions:
should be encouraged instead of allocation of global attribute
types, for functions specific only to one vendor's implementation
of RADIUS, where no interoperability is deemed useful.
However, in practice usage of Vendor-Specific Attributes (VSAs) has
been considerably broader than this. In particular, VSAs have been
used by Standards Development Organizations (SDOs) to define their
own extensions to the RADIUS protocol.
This has caused a number of problems. Since the VSA mechanism was
not designed for interoperability, VSAs do not contain a "mandatory"
bit. As a result, RADIUS clients and servers may not know whether it
is safe to ignore unknown attributes. For example, Section 5 of the
RADIUS specification [RFC2865] states:
IAB Informational [Page 25]
Internet-Draft Design Considerations for Extensions 4 February 2011
A RADIUS server MAY ignore Attributes with an unknown Type. A
RADIUS client MAY ignore Attributes with an unknown Type.
However, in the case where the VSAs pertain to security (e.g.
Filters) it may not be safe to ignore them, since the RADIUS
specification [RFC2865] also states:
A NAS that does not implement a given service MUST NOT implement
the RADIUS attributes for that service. For example, a NAS that
is unable to offer ARAP service MUST NOT implement the RADIUS
attributes for ARAP. A NAS MUST treat a RADIUS access-accept
authorizing an unavailable service as an access-reject instead."
Detailed discussion of the issues arising from this can be found in
"Common Remote Authentication Dial In User Service (RADIUS)
Implementation Issues and Suggested Fixes" [RFC5080] Section 2.5.
Since it was not envisaged that multi-vendor VSA implementations
would need to interoperate, the RADIUS specification [RFC2865] does
not define the data model for VSAs, and allows multiple sub-
attributes to be included within a single Attribute of type 26.
However, this enables VSAs to be defined which would not be
supportable by current implementations if placed within the standard
RADIUS attribute space. This has caused problems in standardizing
widely deployed VSAs, as discussed in "RADIUS Design Guidelines"
[I-D.ietf-radext-design].
In addition to extending RADIUS by use of VSAs, SDOs have also
defined new values of the Service-Type attribute in order to create
new RADIUS commands. Since the RADIUS specification [RFC2865]
defined Service-Type values as being allocated First Come, First
Served (FCFS), this essentially enabled new RADIUS commands to be
allocated without IETF review. This oversight has since been fixed
in "IANA Considerations for RADIUS" [RFC3575].
A.3. TLS Extensions
The Secure Sockets Layer (SSL) v2 protocol was developed by Netscape
to be used to secure online transactions on the Internet. It was
later replaced by SSL v3, also developed by Netscape. SSL v3 was
then further developed by the IETF as the Transport Layer Security
(TLS) 1.0 [RFC2246].
The SSL v3 protocol was not explicitly specified to be extended.
Even TLS 1.0 did not define an extension mechanism explicitly.
However, extension "loopholes" were available. Extension mechanisms
were finally defined in "Transport Layer Security (TLS) Extensions"
[RFC4366]:
IAB Informational [Page 26]
Internet-Draft Design Considerations for Extensions 4 February 2011
o New versions
o New cipher suites
o Compression
o Expanded handshake messages
o New record types
o New handshake messages
The protocol also defines how implementations should handle unknown
extensions.
Of the above extension methods, new versions and expanded handshake
messages have caused the most interoperability problems.
Implementations are supposed to ignore unknown record types but to
reject unknown handshake messages.
The new version support in SSL/TLS includes a capability to define
new versions of the protocol, while allowing newer implementations to
communicate with older implementations. As part of this
functionality some Key Exchange methods include functionality to
prevent version rollback attacks.
The experience with this upgrade functionality in SSL and TLS is
decidedly mixed:
o SSL v2 and SSL v3/TLS are not compatible. It is possible to use
SSL v2 protocol messages to initiate a SSL v3/TLS connection, but
it is not possible to communicate with a SSL v2 implementation
using SSL v3/TLS protocol messages.
o There are implementations that refuse to accept handshakes using
newer versions of the protocol than they support.
o There are other implementations that accept newer versions, but
have implemented the version rollback protection clumsily.
The SSL v2 problem has forced SSL v3 and TLS clients to continue to
use SSL v2 Client Hellos for their initial handshake with almost all
servers until 2006, much longer than would have been desirable, in
order to interoperate with old servers.
The problem with incorrect handling of newer versions has also forced
many clients to actually disable the newer protocol versions, either
by default, or by automatically disabling the functionality, to be
able to connect to such servers. Effectively, this means that the
version rollback protection in SSL and TLS is non-existent if talking
to a fatally compromised older version.
SSL v3 and TLS also permitted expansion of the Client Hello and
Server Hello handshake messages. This functionality was fully
defined by the introduction of TLS Extensions, which makes it
IAB Informational [Page 27]
Internet-Draft Design Considerations for Extensions 4 February 2011
possible to add new functionality to the handshake, such as the name
of the server the client is connecting to, request certificate status
information, indicate Certificate Authority support, maximum record
length, etc. Several of these extensions also introduce new
handshake messages.
It has turned out that many SSL v3 and TLS implementations that do
not support TLS Extensions, did not, as required by the protocol
specifications, ignore the unknown extensions, but instead failed to
establish connections. Several of the implementations behaving in
this manner are used by high profile Internet sites, such as online
banking sites, and this has caused a significant delay in the
deployment of clients supporting TLS Extensions, and several of the
clients that have enabled support are using heuristics that allow
them to disable the functionality when they detect a problem.
Looking forward, the protocol version problem, in particular, can
cause future security problems for the TLS protocol. The strength of
the digest algorithms (MD5 and SHA-1) used by SSL and TLS is
weakening. If MD5 and SHA-1 weaken to the point where it is feasible
to mount successful attacks against older SSL and TLS versions, the
current error recovery used by clients would become a security
vulnerability (among many other serious problems for the Internet).
To address this issue, TLS 1.2 [RFC5246] makes use of a newer
cryptographic hash algorithm (SHA-256) during the TLS handshake by
default. Legacy ciphersuites can still be used to protect
application data, but new ciphersuites are specified for data
protection as well as for authentication within the TLS handshake.
The hashing method can also be negotiated via a Hello extension.
Implementations are encouraged to implement new ciphersuites, and to
enable the negotiation of the ciphersuite used during a TLS session
to be governed by policy, thus enabling a more rapid transition away
from weakened ciphersuites.
The lesson to be drawn from this experience is that it isn't
sufficient to design extensibility carefully; it must also be
implemented carefully by every implementer, without exception. Test
suites and certification programs can help provide incentives for
implementers to pay attention to implementing extensibility
mechanisms correctly.
A.4. L2TP Extensions
Layer Two Tunneling Protocol (L2TP) [RFC2661] carries Attribute-Value
Pairs (AVPs), with most AVPs having no semantics to the L2TP protocol
itself. However, it should be noted that L2TP message types are
identified by a Message Type AVP (Attribute Type 0) with specific AVP
IAB Informational [Page 28]
Internet-Draft Design Considerations for Extensions 4 February 2011
values indicating the actual message type. Thus, extensions relating
to Message Type AVPs would likely be considered major extensions.
L2TP also provides for Vendor-Specific AVPs. Because everything in
L2TP is encoded using AVPs, it would be easy to define vendor-
specific AVPs that would be considered major extensions.
L2TP also provides for a "mandatory" bit in AVPs. Recipients of L2TP
messages containing AVPs they do not understand but that have the
mandatory bit set, are expected to reject the message and terminate
the tunnel or session the message refers to. This leads to
interesting interoperability issues, because a sender can include a
vendor-specific AVP with the M-bit set, which then causes the
recipient to not interoperate with the sender. This sort of behavior
is counter to the IETF ideals, as implementations of the IETF
standard should interoperate successfully with other implementations
and not require the implementation of non-IETF extensions in order to
interoperate successfully. Section 4.2 of the L2TP specification
[RFC2661] includes specific wording on this point, though there was
significant debate at the time as to whether such language was by
itself sufficient.
Fortunately, it does not appear that the potential problems described
above have yet become a problem in practice. At the time of this
writing, the authors are not aware of the existence of any vendor-
specific AVPs that also set the M-bit.
Change log [RFC Editor: please remove this section]
draft-iab-extension-recs-04: 2011-2-3. Added a section on
cryptographic agility. Additional reorganization.
draft-iab-extension-recs-03: 2011-1-25. Updates and reorganization
to reflect comments from the IETF community.
draft-iab-extension-recs-02: 2010-7-12. Updates by Bernard Aboba
draft-iab-extension-recs-01: 2010-4-7. Updates by Stuart
Cheshire.
draft-iab-extension-recs-00: 2009-4-24. Updated boilerplate,
author list.
draft-carpenter-extension-recs-04: 2008-10-24. Updated author
addresses, fixed editorial issues.
draft-carpenter-extension-recs-03: 2008-10-17. Updated references,
added material relating to versioning.
IAB Informational [Page 29]
Internet-Draft Design Considerations for Extensions 4 February 2011
draft-carpenter-extension-recs-02: 2007-06-15. Reorganized Sections
2 and 3.
draft-carpenter-extension-recs-01: 2007-03-04. Updated according to
comments, especially the wording about TLS, added various specific
examples.
draft-carpenter-extension-recs-00: original version, 2006-10-12.
Derived from draft-iesg-vendor-extensions-02.txt dated 2004-06-04 by
focusing on architectural issues; the more procedural issues in that
draft were moved to RFC 4775.
Authors' Addresses
Brian Carpenter
Department of Computer Science
University of Auckland
PB 92019
Auckland, 1142
New Zealand
Email: brian.e.carpenter@gmail.com
Bernard Aboba
Microsoft Corporation
One Microsoft Way
Redmond, WA 98052
EMail: bernard_aboba@hotmail.com
Stuart Cheshire
Apple Computer, Inc.
1 Infinite Loop
Cupertino, CA 95014
EMail: cheshire@apple.com
IAB Informational [Page 30]
Html markup produced by rfcmarkup 1.120, available from
https://tools.ietf.org/tools/rfcmarkup/